finalcutserver on lionserver 難解求助

[northcab]

各位大大好：
小弟的系統原來是10.6.8運行finalcutserver這個軟體非常順暢
不過
升級到LION SERVER 之後finalcutserver 的JAVA client 就無法運作了
finalcutserver運作的模式是到 http://HOSTNAME/finacutserver
就會出現下載JAVA client 的網頁 接著進行下載即可

但目前在LION SERVER中，我只能連到http://HOSTNAME/
如果連到http://HOSTNAME/finacutserver 就會出現找不到網頁的訊息

根據爬文的結果出現以下解決方法 大意是說 轉換使用者的登入認證方法 我試著照辦 沒有出現可以正常使用的結果 請看紅字部份
http://factorial.co.nz/cliptouchhelp/#lionfcsvr 原文鏈結

Installing Final Cut Server on Lion and Lion Server

Final Cut Server installs okay on OS X Lion and Lion Server, but in its default configuration authentication fails from both the Java Client, and from ClipTouch. In order to use Final Cut Server running on OS X Lion, please run the following commands:
Switch the Final Cut Server authentication mode to use CRAM-MD5 passwords by executing following command in Terminal:

sudo defaults write /Library/Preferences/com.apple.FinalCutServer.settings "AUTH_TYPE" -int 2
Restart Final Cut Server via the System Preference pane.

If your Final Cut Server is installed on OS X Lion Client, you must also enable CRAM-MD5 password support for any user accounts you have configured to access Final Cut Server.

For each user account accessing Final Cut Server:

sudo pwpolicy -u username -sethashtypes CRAM-MD5 on
And then reset the password of the user using:

sudo pwpolicy -a username -u username -setpassword
(The password reset can also be performed via System Preferences).

Optionally enable CRAM-MD5 password support for new users:

sudo pwpolicy -setglobalhashtypes CRAM-MD5 on
Please note that Lion Server has CRAM-MD5 enabled by default for user accounts and does not require this step.

If your Final Cut Server is installed on Lion Server, you have to also manually configure the webserver to show the Final Cut Server start page. Depending on the webserver sites configuration you use, simply add the required rewrite rule to the appropriate virtual host. The required lines of http configuration can be found here:
/Library/Application\ Support/Final\ Cut\ Server/Final\ Cut\ Server.bundle/Contents/Resources/share/conf/client_apache2.conf
Please note that on Lion Client the automatic configuration of the webserver works correctly and this step is not required.
Your Final Cut Server is now configured to accept authentication from both the Java Client, and ClipTouch 1.2.

紅字的部份 我不知道怎麼做會是正確的 也許也是最關鍵的部份
或者是說 我在文章中的解說中
誤解了哪一個步驟
請大大們
幫忙看一下
指引個明燈
感謝多多

[ViewFinder]

意思是去打開上述的檔案，將裡面的文字 copy 出來，加在你的 virtual host 設定檔案裡。只有你的 virtual host 設定檔案是那個就看你的設定而定了。應該是在 /etc/apache2 或其子目錄底下的某個 .conf 檔案。

[northcab]

意思是去打開上述的檔案，將裡面的文字 copy 出來，加在你的 virtual host 設定檔案裡。只有你的 virtual host 設定檔案是那個就看你的設定而定了。應該是在 /etc/apache2 或其子目錄底下的某個 .conf 檔案。

感謝大大的回應
我會再試試
不過先前
這樣試
依然沒有反應
不知道哪裡出錯？？

[ViewFinder]

加完記得要重啓apache2

[ViewFinder]

我沒裝 lion server，所以也不是很確定。你有用 virtualhost 嗎？

[northcab]

您說的這兩樣
我都不確定
可否賜教
謝謝

[northcab]

我得到的訊息如下：

Not Found

The requested URL /finalcutserver was not found on this server.

Apache/2.2.21 (Unix) mod_ssl/2.2.21 OpenSSL/0.9.8r DAV/2 PHP/5.3.8 with Suhosin-Patch Server at 192.168.10.77 Port 443